E-mail: Info@ktoolinc.com
Phone# 800-377-3056
ktool%20small.png
Advantages of K-Tool, Inc.
Slotting Cuttters / Half Side Mills
K-Tool, Inc.
SCSM
#00 Series
Shell Mount
Slotting Cutters
 Applications: Slotting - Half Side Milling

 (1) Shell Mount Design Provides Rigid Mounting on a Face Mill Style Holder
 (2) These Cutters May be Set up for L.H., R.H., or Stagger Tooth to cut a full slot
 (3) Set Cutter Staggerd Tooth to Achieve a Specific Width of Cut
 (4) Initial W.O.C. Set With a Dial Indicator or Presetter
 (5) K-Tool, Inc. Can Pre Set the Cutter to Your W.O.C. at no Charge
 (6) Inserts are Held in Cartridges to Protect Tool & Eliminate the Expense of Rebuilding
 (7) Positive Top Insert for High Shear Cutting Action
 (8) 4 Cutting Edges Per Insert
Slotting Cutter
Speed & Feed Info.
 Material
S.F.M.
I.P.T.
Mild & Low Carbon Steel
Ex. 1018, 1020, 1117,1141,12L14
 800 -1200 
 .002 - .003 
High Carbon & Alloy Steel
Ex. 1045, 4140, 4340, 52100,8620
 500 - 800 
 .002 - .003 
Lower Carbon Tool Steel
Ex. P-20, H-13, S-7
 400 - 700 
 .002 - .003 
Tool Steel
Ex. A-2, A-6, D-2, M-2
 300 - 600  
 .001 - .003 
Stainless Steel
Ex.304, 316, 420, 15-5PH, 17-4PH
 300 - 600  
 .002 - .003 
Iron
Ex. Cast, Ductile, Nodular
 600 -1000
 .002 - .003 
Nickel &Titanium Alloy
Ex. Inconel, Hastelloy, TI-6AL-4V
 120 -180  
 .001 - .002 
Non-Ferrous metals
Ex. Aluminum, Bronze, Brass 
 1000 - 2500
 .002 - .004 
 Tool #
 D  
  Flutes 
 W.O.C. 
 D.O.C. 
 Bore 
Key 
Hub
 L 
SCSM-4000 
4.000 
 10
.250 - .340 
.875 
 1.000 
 .375 
 2.000 
 1.625 
SCSM-5000 
 5.000 
 12
.250 - .340 
1.062 
 1.250 
 .500 
 2.625 
 1.750 
SCSM-6000 
 6.000 
 14
.250 - .340 
1.562 
 1.250 
 .500 
 2.625 
 1.750 

Slotting Cutters / Half Side Mills - Shell mount
Series #00

Adjustable High Shear Cartridge Style Slotting Cutters

Back
 Tool #
 Cartridge  
  Wedge 
  Wedge Screw  
  Insert  
  Screw 
  Wrench 
SCSM-4000 
 #1511C - RH/LH 
 #1
 #6
 SPEB-1511CB 
 164T 
 T-6 
SCSM-5000 
#1511C - RH/LH
 #1
 #6
SPEB-1511CB
164T
T-6
SCSM-6000 
#1511C - RH/LH 
 #1
 #6
SPEB-1511CB
164T
T-6

.250 - .340 W.O.C.

00%20rh.png
R.H.
Cartridge
00%20lh.png
L.H.
Cartridge
SCSM-4000 Shown with L.H. & R.H. cartridges to cut full slot
shell%20mount%20slotting%20cutter%2000.png k-tool_doc119003.png scsm%20drawing.png slotting.png side%20slotting.png
Slotting
Side
Slotting
Face Milling
backfacing.png
Back Face
Milling
periphery%20milling.png
Periphery Milling
When cutter is set for a full slot, Tools are to be
run as 1/2 the number of flutes effective.
Note:
Initial width to be set
 with dial indicator.
K-Tool can set cutter
 at no charge before shipping.
Cutters can be used as


Half Side: Right Hand or left hand
Full Slot: W.O.C required
facemilling.png
Bore
D
L
W.O.C.
D.O.C.
Hub
Screw Torque
Information
Insert Information
Click here for insert grade Descriptions
 Insert #
I.C.
T
R
Insert Grades
 .187
 .082
 .015
 X33, X40
speb-cb.png
Home
Products
About Us
Contact Us
Representatives
Special Tools
Test Tool
Request Form
Tech Support
K-Tool, Inc.
Made in the USA
Phone# 800-377-3056
E-mail: Info@ktoolinc.com